본문 바로가기
HOME> 저널/프로시딩 > 저널/프로시딩 검색상세

저널/프로시딩 상세정보

권호별목차 / 소장처보기

H : 소장처정보

T : 목차정보

바이오시스템공학 = Journal of biosystems engineering 9건

  1. [국내논문]   농용 트랙터 연료소모량에 미치는 요인분석   피인용횟수: 3

    박석호 (Researcher, National Academy of Agricultural Science, RDA ) , 김영중 (National Academy of Agricultural Science, RDA ) , 임동혁 (National Academy of Agricultural Science, RDA ) , 김충길 (National Academy of Agricultural Science, RDA ) , 장양 (Daedong Industrial Co., Ltd. ) , 김성수 (Daedong Industrial Co., Ltd.)
    바이오시스템공학 = Journal of biosystems engineering v.35 no.3 ,pp. 151 - 157 , 2010 , 1738-1266 ,

    초록

    The objective of this study was to analyze the factors affecting on fuel consumption of agricultural tractor. According to the statistical analysis, fuel consumption of agricultural tractor was considerably influenced by kind of operation, throttle engine speed and gear steps of tractor but much less by kind of soil. Specific fuel consumption of the tractor in plowing, dry paddy tilling, wet paddy tilling and wet paddy levelling was 0.33~0.36, 0.30~0.45, 0.19~0.34, 0.28~0.39 L/ $kW{\cdot}h$ , respectively, and $CO_2$ emission was 0.36~0.45, 0.35~0.58, 0.22~0.42, 0.24~0.37 kg/ $kW{\cdot}h$ , respectively. Specific fuel consumption and $CO_2$ emission increased as throttle engine speed increased but reversely proportional with gear step of tractor, by which one can reduce fuel consumption and $CO_2$ emission with practicing of "Gear up & Throttle Down" technique in paddy operations.

    원문보기

    원문보기
    무료다운로드 유료다운로드

    회원님의 원문열람 권한에 따라 열람이 불가능 할 수 있으며 권한이 없는 경우 해당 사이트의 정책에 따라 회원가입 및 유료구매가 필요할 수 있습니다.이동하는 사이트에서의 모든 정보이용은 NDSL과 무관합니다.

    NDSL에서는 해당 원문을 복사서비스하고 있습니다. 아래의 원문복사신청 또는 장바구니담기를 통하여 원문복사서비스 이용이 가능합니다.

    이미지

    Fig. 1 이미지
  2. [국내논문]   비 정제 팜유에 대한 분무특성의 실험적 연구  

    최승훈 (Chonbuk National University ) , 오영택 (Research Center of Industrial Technology, Chonbuk National University, Dept. of Mechanical Engineering, Chonbuk National University)
    바이오시스템공학 = Journal of biosystems engineering v.35 no.3 ,pp. 158 - 162 , 2010 , 1738-1266 ,

    초록

    The effect of fuel injection characteristics on engine performance has been known for improving fuel economy and emission reduction. In this study, the spray characteristics of crude palm oil blended fuel with conventional diesel fuel was investigated. The experiments were performed to evaluate the effect of crude palm oil blending ratio and injection pressure on the spray behavior. The droplet size of injected fuel was analyzed through laser diffraction particle analyzer (LDPA). Also, spray atomization characteristics were investigated in terms of Sauter mean diameter (SMD) and droplet distribution at various injection conditions. Fuel containing crude palm oil has different spray pattern on account of the high viscosity. Through those experimental results, we found that the increase of blending ratio made droplet size larger, SMD of biodiesel 100% was increased 30.2% than that of diesel fuel 100% under injection pressure of 60 MPa.

    원문보기

    원문보기
    무료다운로드 유료다운로드

    회원님의 원문열람 권한에 따라 열람이 불가능 할 수 있으며 권한이 없는 경우 해당 사이트의 정책에 따라 회원가입 및 유료구매가 필요할 수 있습니다.이동하는 사이트에서의 모든 정보이용은 NDSL과 무관합니다.

    NDSL에서는 해당 원문을 복사서비스하고 있습니다. 아래의 원문복사신청 또는 장바구니담기를 통하여 원문복사서비스 이용이 가능합니다.

    이미지

    Fig. 1 이미지
  3. [국내논문]   공기분사 및 회전 롤러를 이용한 옥수수 포엽 제거장치의 시험  

    박회만 (Department of Agricultural Engineering, National Academy of Agricultural Science ) , 조광환 (Department of Agricultural Engineering, National Academy of Agricultural Science ) , 홍성기 (Department of Agricultural Engineering, National Academy of Agricultural Science ) , 이선호 (Department of Agricultural Engineering, National Academy of Agricultural Science)
    바이오시스템공학 = Journal of biosystems engineering v.35 no.3 ,pp. 163 - 168 , 2010 , 1738-1266 ,

    초록

    With income growth and "well-being" trends, sales of corn has been increased recently. Corns are processed at processing facilities on the main production site. Corn processing steps include removing bract, steaming, vacuum packing, and storing. To replace manual corn bract removing, some bract removing machines were imported and used. However, the machines were abandoned shortly, because of high damaging ratio of corns. In this research, factors of successful bract removing was studied with rotating rollers and air-injection nozzles to develop corn bract removing system. The test device was composed of a cylindrical roller, an air spray nozzle, a regulator, and a motor. Designing factors were roller type, diameter of air spraying nozzle, spraying angle, and spraying pressure. The measured factors were bract removing rate and damaging rate. It was found that optimum cylindrical roller surface shape was cylindrical roller and linear grove roller. This roller shape produced lowest damaging rate. Test results of the efficacy of preprocessing showed that the air spraying after preprocessing produced highest performance. The rotational speed and inclination of the roller didn't affect the bract removing performance. Optimum injection angle of the air jet nozzle was $70^{\circ}$ . To increase bract removing rate and to reduce corn damage, required injection pressure and injection nozzle diameter were decided to less than 0.4 MPa and 2.5 mm, respectively. More than 3 times of nozzle passing produced good bract removing performance and there were no significant difference between the number of passing times.

    원문보기

    원문보기
    무료다운로드 유료다운로드

    회원님의 원문열람 권한에 따라 열람이 불가능 할 수 있으며 권한이 없는 경우 해당 사이트의 정책에 따라 회원가입 및 유료구매가 필요할 수 있습니다.이동하는 사이트에서의 모든 정보이용은 NDSL과 무관합니다.

    NDSL에서는 해당 원문을 복사서비스하고 있습니다. 아래의 원문복사신청 또는 장바구니담기를 통하여 원문복사서비스 이용이 가능합니다.

    이미지

    Fig. 1 이미지
  4. [국내논문]   정백공정 중 연삭공정이 쌀 품질에 미치는 영향  

    강태환 (Agriculture Science & Technology Research Institute, Chungbuk National University ) , 녕효봉 (Dept. of Biosystems Engineering, Chungbuk National University ) , 한충수 (Dept. of Biosystems Engineering, Chungbuk National University ) , 조성찬 (Dept. of Biosystems Engineering, Chungbuk National University)
    바이오시스템공학 = Journal of biosystems engineering v.35 no.3 ,pp. 169 - 174 , 2010 , 1738-1266 ,

    초록

    This study was conducted to investigate the effect of abrasive processing and non abrasive processing in the milling process on the quality of rice. The effect was analyzed based on the factor such as whiteness, grain temperature, moisture content, crack and broken rice ratio. The results were as followings. Whiteness of abrasive rice was the same as non abrasive rice. The rice temperature increase of abrasive rice was $1.6^{\circ}C$ lower than non abrasive rice. The crack ratio was increased in the process of milling and non abrasive rice showed higher values than abrasive rice. The broken rice ratio of the using abrasive processing was about 0.05% lower than that of non abrasive processing. The moisture content decreased in the process of milling regardless of the use abrasive rice milling machine.

    원문보기

    원문보기
    무료다운로드 유료다운로드

    회원님의 원문열람 권한에 따라 열람이 불가능 할 수 있으며 권한이 없는 경우 해당 사이트의 정책에 따라 회원가입 및 유료구매가 필요할 수 있습니다.이동하는 사이트에서의 모든 정보이용은 NDSL과 무관합니다.

    NDSL에서는 해당 원문을 복사서비스하고 있습니다. 아래의 원문복사신청 또는 장바구니담기를 통하여 원문복사서비스 이용이 가능합니다.

    이미지

    Fig. 1 이미지
  5. [국내논문]   고주파 저항방식 함수율계의 보정식 개발 및 특성평가  

    전홍영 (Department of Agriculture Agricultural Research Service ) , 강태환 (Agriculture Science & Technology Research Institute, Chungbuk National University ) , 한충수 (Dept. of Biosystems Engineering, Chungbuk National University)
    바이오시스템공학 = Journal of biosystems engineering v.35 no.3 ,pp. 175 - 181 , 2010 , 1738-1266 ,

    초록

    This study compared moisture content measured by moisture meter of microwave resistance type(MMMRT) and standard moisture content of paddy, and developed the correction equation using linear and curvilinear regression analysis, and to explore its significance test. The correction factor according to the range of moisture content was developed to improve the measurement precision of MMMRT. The results were as followings. The coefficients of determination of correction equation by linear and curvilinear regression analysis with comparing the MMMRT and standard moisture content were 0.946 and 0.968, respectively. The moisture content error of MMMRT and standard moisture content measured after the MMMRT were corrected by moisture content rate of every 5% using the correction equation by curvilinear regression analysis appeared with 0~0.5% and 0.9~1.8% respectively in the moisture content range of 15~20% and 20~25%.

    원문보기

    원문보기
    무료다운로드 유료다운로드

    회원님의 원문열람 권한에 따라 열람이 불가능 할 수 있으며 권한이 없는 경우 해당 사이트의 정책에 따라 회원가입 및 유료구매가 필요할 수 있습니다.이동하는 사이트에서의 모든 정보이용은 NDSL과 무관합니다.

    NDSL에서는 해당 원문을 복사서비스하고 있습니다. 아래의 원문복사신청 또는 장바구니담기를 통하여 원문복사서비스 이용이 가능합니다.

    이미지

    Fig. 1 이미지
  6. [국내논문]   모의수송 중 진동피로에 의한 복숭아의 손상   피인용횟수: 2

    최승렬 (National Academy of Agricultural Science, RDA ) , 이영희 (National Academy of Agricultural Science, RDA ) , 최동수 (National Academy of Agricultural Science, RDA ) , 김만수 (Dept. of Biosystems Machinery Engineering, Chungnam National University)
    바이오시스템공학 = Journal of biosystems engineering v.35 no.3 ,pp. 182 - 188 , 2010 , 1738-1266 ,

    초록

    Post-Harvest processing engineering is a field that studies prevention of the quality change of agricultural products during sorting, packaging, storage, and distribution after harvested. In distribution steps, agricultural products could be damaged by physical force, it is the main reason of low quality and they lost value of commodities. This study was performed to find the vibration characteristics of the peach, and to find the extent of the damage on the peach by fatigue stress. The vibration data was obtained on expressway and the vibration characteristics of peach was used to find the damage on the peach. To analyze the vibration characteristics of peach, the resonance frequency and vibration transmissibility were measured. The resonance frequency of the peach was 167.98 Hz and the transmissibility was 4.06 at resonance point. It was 150 ~ 250 Hz that the transmissibility was more than 1. And the transmissibility in simulated test was measured. When the trasmissibility was more than 1, the range was 15 ~ 65 Hz, and when it was less than 1, the range was 65 ~ 175 Hz. When the transmissibility was about 1, the range was 5 ~ 15 Hz. The damage and the vibration cycle numbers of peaches were compared with input frequency and acceleration. More damage and less cycle number happened in 30 Hz than in 62.5 Hz. The reason was that the transmissibility of 30 Hz was higher and the vibration displacement in lower frequency was more. The more acceleration and cycle number increased, the more the bruising volume of peaches increased. The bruising volume ratio for vibration fatigue was measured according to input acceleration and cycle number. Using measured data, regression models for bruising volume ratio(BVR) was developed as a function of the acceleration(A) and cycle number(CN) as follows. BVR = a * $A^b*$ $(CN)^c$

    원문보기

    원문보기
    무료다운로드 유료다운로드

    회원님의 원문열람 권한에 따라 열람이 불가능 할 수 있으며 권한이 없는 경우 해당 사이트의 정책에 따라 회원가입 및 유료구매가 필요할 수 있습니다.이동하는 사이트에서의 모든 정보이용은 NDSL과 무관합니다.

    NDSL에서는 해당 원문을 복사서비스하고 있습니다. 아래의 원문복사신청 또는 장바구니담기를 통하여 원문복사서비스 이용이 가능합니다.

    이미지

    Fig. 1 이미지
  7. [국내논문]   과실 경도측정을 위한 비접촉 초음파 변환기 연구   피인용횟수: 1

    이상대 (Agricultural Research Service, USDA ) , 하태훈 (Dept. of Medical Physics, University of Science & Technology ) , 김기복 (Center for Safety Measurement, Korea Research Institute of Standards and Science ) , 김만수 (Dept. Biosystems Machinery Engineering, Chungnam National University)
    바이오시스템공학 = Journal of biosystems engineering v.35 no.3 ,pp. 189 - 196 , 2010 , 1738-1266 ,

    초록

    This study was conducted to develop an non-contact ultrasonic transducer for measurement of fruit firmness. The center frequency of non-contact ultrasonic transducer was 500 kHz. As an active element of non-contact ultrasonic transducer, the 1-3 piezoelectric composite material was selected. That material has high piezoelectric properties such as electro-mechanical coupling factor, $k_t$ and piezoelectric voltage constant, $d_{33}$ and also that material has low acoustical impedance which enables to matching the acoustical impedances between piezoelectric material and air. As a front matching material between 1-3 piezoelectric composite material and air, various kinds of paper with different thickness were tested. To control the dead-zone of the fabricated non-contact ultrasonic transducer, the backing material composed of epoxy resin and tungsten powder were made and evaluated. The fabricated non-contact ultrasonic transducer for fruit showed that the cneter frequency, bandwidth and beamwidth were approximately 480 kHz, 30 % and 12 mm, respectively. It was concluded that non-contact measurement of apple firmness would be possible by using the fabricated non-contact ultrasonic transducer.

    원문보기

    원문보기
    무료다운로드 유료다운로드

    회원님의 원문열람 권한에 따라 열람이 불가능 할 수 있으며 권한이 없는 경우 해당 사이트의 정책에 따라 회원가입 및 유료구매가 필요할 수 있습니다.이동하는 사이트에서의 모든 정보이용은 NDSL과 무관합니다.

    NDSL에서는 해당 원문을 복사서비스하고 있습니다. 아래의 원문복사신청 또는 장바구니담기를 통하여 원문복사서비스 이용이 가능합니다.

    이미지

    Fig. 1 이미지
  8. [국내논문]   영상처리식 온라인 품위판정을 위한 현미의 정렬공급장치   피인용횟수: 1

    김태민 (Korea Advanced Institute of Science and Technology ) , 노상하 (Department of Biosystems Engineering, Seoul National University)
    바이오시스템공학 = Journal of biosystems engineering v.35 no.3 ,pp. 197 - 205 , 2010 , 1738-1266 ,

    초록

    An automatic echelon feeder of brown rice was presented for quality inspection system using color image processing. A echelon feeder was developed with vibratory feeder and cylindrical indent singulator having oblique light. The vibratory feeder consisted of a hopper, electromagnetic vibrator and multichannel grooves and supply the grain sample to the singulator. The feeding performance such as feed rate, blocking frequency of the channel was dependent on the size of groove and vibration pattern. A cylindrical indent singulator consisted of a rotating cylinder, prisms and a tungsten-halogen light source. It delivered grain kernels under the camera in a echelon form and illuminate the kernels with oblique ray and ambient light. The size of the indents installed on the surface of the rotating cylinder was determined by the dimensions of the paddy and a small triangular prism was placed in each indent to apply $ 20^{\circ}$ oblique light to the grain kernel.

    원문보기

    원문보기
    무료다운로드 유료다운로드

    회원님의 원문열람 권한에 따라 열람이 불가능 할 수 있으며 권한이 없는 경우 해당 사이트의 정책에 따라 회원가입 및 유료구매가 필요할 수 있습니다.이동하는 사이트에서의 모든 정보이용은 NDSL과 무관합니다.

    NDSL에서는 해당 원문을 복사서비스하고 있습니다. 아래의 원문복사신청 또는 장바구니담기를 통하여 원문복사서비스 이용이 가능합니다.

    이미지

    Fig. 1 이미지
  9. [국내논문]   디지털 인체 모델을 이용한 콤바인 수확 작업의 근골격계 상해요소 분석   피인용횟수: 1

    김영진 (Dept. of Biomechatronics Engineering, Sungkyunkwan University ) , 임용훈 (Dept. of Biomechatronics Engineering, Sungkyunkwan University ) , 이경숙 (Dept. of Biomechatronics Engineering, Sungkyunkwan University ) , 최창현 (Dept. of Biomechatronics Engineering, Sungkyunkwan University ) , 문정환 (Dept. of Biomechatronics Engineering, Sungkyunkwan University)
    바이오시스템공학 = Journal of biosystems engineering v.35 no.3 ,pp. 206 - 213 , 2010 , 1738-1266 ,

    초록

    The purpose of this study is to analyze musculoskeletal injuries in combine harvesting operation using a digital human model. In order to analyze problems in combine harvesting operation, the operations were broken into 5 work processes and then we preformed ergonomic and biomechanical analyses such as RULA test, Comfort Assessment and joint kinetic analysis for the each process. As a result, there was a clear need to change the combine operating environment, as the RULA score ranged from 4 to 7. In addition, we could find two major musculoskeletal injury factors which are the standing posture with upperbody forward tilting and inappropriate location of operating levers.

    원문보기

    원문보기
    무료다운로드 유료다운로드

    회원님의 원문열람 권한에 따라 열람이 불가능 할 수 있으며 권한이 없는 경우 해당 사이트의 정책에 따라 회원가입 및 유료구매가 필요할 수 있습니다.이동하는 사이트에서의 모든 정보이용은 NDSL과 무관합니다.

    NDSL에서는 해당 원문을 복사서비스하고 있습니다. 아래의 원문복사신청 또는 장바구니담기를 통하여 원문복사서비스 이용이 가능합니다.

    이미지

    Fig. 1 이미지

논문관련 이미지